oil level CHRYSLER 200 2012 1.G User Guide

ENGINE BREAK-IN RECOMMENDATIONS
• A long break-in period is not required for the engine and drivetrain (transmission andaxle) in your vehicle.
• Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
• While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be
detrimental and should be avoided.
• The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under
which vehicle operations will occur. For the recommended viscosity and quality grades,
refer to “Maintaining Your Vehicle”.
NOTE:A new engine may consume some oil during its first few thousand miles (kilometers)
of operation. This should be considered a normal part of the break-in and not interpreted as an
indication of difficulty.
CAUTION!
Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result.
TURN SIGNAL/LIGHTS LEVER
Headlights/Parking Lights/Automatic Headlights
• Rotate the end of the lever to the first detent for parking lights, the second
detent for headlights
and the third detent for AUTO.
• When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels.
OPERATING YOUR VEHICLE
17

FLUIDS AND CAPACITIES
ComponentFluid, Lubricant, or Genuine Part Capacities
Engine Coolant 2.4L MOPAR® Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT
(Hybrid Organic Additive
Technology) or equivalent. 7.7 Quarts (7.3 Liters)
Includes heater and coolant
recovery bottle filled to
MAX level.
Engine Coolant 3.6L MOPAR® Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT
(Hybrid Organic Additive
Technology) or equivalent. 11.6 Quarts (11 Liters)
Includes heater and coolant
recovery bottle filled to
MAX level.
Engine Oil with Filter 2.4L API Certified SAE 5W-20 engine oil, meeting the requirements of
Chrysler Material Standard
MS-6395. Refer to the engine oil
filler cap for correct SAE grade. 4.5 Quarts (4.4 Liters)
Engine Oil with Filter 3.6L API Certified SAE 5W-30 engine oil, meeting Chrysler Material Standard
MS-6395. Refer to your engine oil
filler cap for correct SAE grade. 6 Quarts (5.6 Liters)
Engine Oil Filter 2.4L &
3.6L MOPAR® Engine Oil Filter or
equivalent.
—
Spark Plugs 2.4L except
PZEV ZFR5F-11 (Gap 0.043 in [1.11 mm])
—
Spark Plugs 2.4L with PZEV ZFR5AP (Gap 0.031 in [0.8 mm]) —
Spark Plugs 3.6L RER8ZWYCB4 (Gap 0.043 in
[1.1 mm]) —
Automatic Transmission –
Four-Speed MOPAR® ATF+4® Automatic
Transmission Fluid or equivalent
licensed ATF+4® product. —
Automatic Transmission –
Six-Speed (62TE Only) MOPAR® ATF+4® Automatic
Transmission Fluid or equivalent
licensed ATF+4® product. —
Brake Master Cylinder MOPAR® DOT 3 and SAE J1703 should be used or equivalent. If
DOT 3 is not available, then DOT 4
is acceptable. Use only
recommended brake fluids. —
Power Steering Reservoir MOPAR® Power Steering Fluid + 4 or MOPAR® ATF+4® Automatic
Transmission Fluid or equivalent
licensed ATF+4® product. —
Fuel Selection – All Engines
(except 2.4L PZEV) 87 Octane
16.9 Gallons (64 Liters)
(Approximate)
Fuel Selection 2.4L PZEV 87 Octane 18.5 Gallons (70 Liters)
(Approximate)
MAINTAINING YOUR VEHICLE
85